【BlueRobotics】BlueROV2用 LED R2 (New バージョン) 4個 1セット [B181212050]  DJI ドローン|PGY SUBLUE HOBBYWING 総代理店 セキドオンラインストア

ゲスト 様

【BlueRobotics】BlueROV2用 LED R2 (New バージョン) 4個 1セット

※写真はイメージです。

型番 B181212050
販売価格 42,000円(税込45,360円)
商品ポイント 453 ポイント
在庫状況 完売/入荷待ち

申し訳ございません
この商品は好評につき品切れ中です

対応機種:BlueRobotics BlueROV2



ご入金確認時より約4〜6週間で入荷いたします。
【お取り寄せ対象商品についての注意事項】

◆この商品はご入金後にキャンセルする事ができません。商品内容をよくご理解の上ご注文をお願い申しあげます。

◆この商品は上記にて入荷時期を記載しておりますが、メーカーの都合により納期が前後する場合がございます。なお、大幅な納期遅れ、欠品となった場合には当社よりご連絡させて頂きます。

◆通常販売商品との同時注文について
お取り寄せ対象商品と通常販売商品を同時にご注文いただいた場合、お取り寄せ対象商品が入荷し次第、同時発送となります。先行して通常販売商品の発送を希望される場合は、お取り寄せ対象商品とは別にご注文ください。



【商品説明】

The Lumen Subsea Light is a blindingly bright LED light for use on ROVs, AUVs, and other subsea applications. We designed this light specifically for this purpose and it has a few neat features:

Fully dimmable control using a PWM servo signal (1100-1900 μs)
Simple on/off control with no signal needed
Daisy-chainable to connect multiple lights from a single connection
Automatic, smart over-temperature compensation for maximum light output and safety in air
New in R2: Built-in mounting holes on the side of the case (M3 thread)
New in R2: Exponential brightness control with much lower minimum brightness output
New in R2: 950m depth rating Using a high-efficiency Cree XLamp MK-R LED, the light outputs over 1500 lumens at 15 Watts – brighter than most car headlights! It has a 135 degree beam angle for wide illumination in front of an ROV. The color temperature is 6200K, similar to most dive lights and ROV lights.

In addition to really high brightness, the Lumen R2 is designed for very low brightness output, which is important to be able to illuminate the scene without washing out the colors or brightness. An exponential brightness curve makes it intuitive to use effectively.

Lumen R2 Brightness Range It’s housed in a rugged hard-anodized aluminum enclosure with two cable penetrators at the rear, allowing it to go to a depth of 950m. The specially designed injection molded acrylic lens ensures a consistent beam angle in both air and water. The case has a built-in mounting bracket with two M3 threaded holes for mounting to your vehicle.

For those who want to use the light in other applications, like scuba diving, the light can be operated without a PWM signal. Just connect the yellow signal wire to the power wire and it will turn on! A switch can be used here to make this even more convenient.

The light operates on 10-48V inputs and can accept PWM signals from 3-48V! It is compatible with many common boards like the Arduino, Raspberry Pi, and PixHawk. The case warms up to a comfortable 55°C (131°F) when operated in air and stays much cooler in water.

Note: We recommend that you don’t look directly into this light to avoid any damage to your eyes!

【商品サイズ】

LED R2 (New バージョン) 4個 1セット | 商品サイズ

【スペック】

Electrical
Supply Voltage (V in ) 7 - 48 volts
Full Brightness Supply Voltage (V in ) 10 - 48 volts
PWM Logic Voltage 3 - 48 volts
Peak Current 15 / V in amps
Light
Maximum Brightness 1,500 lumens
Color Temperature 6,200 kelvin
Beam Angle 135 degrees in water
Cable
Cable Diameter 4.3 mm
Cable Length (between lights) 1 m
Cable Length (between red penetrator and first light) 0.75 m
Cable Jacket Black Urethane
Conductor Insulation Polypropylene
Conductor Gauge 22 AWG
Wires Black - Ground
Red - Power
Yellow - Signal
Physical
Pressure Rating 950 m
Overall Length 68.9 mm
Overall Diameter 37 mm
Bracket Mounting Hole Spacing 19 mm
Bracket Screw Size M3
Weight in Air (w/ 1m cable) 102 g
Weight in Water (w/ 1m cable) 53 g
Maximum Temperature when Run in Air 55° C

【セット内容】

●Lumen Subsea Light Set, pre-connected with 4 lights × 1
●Stainless steel M3 mounting screws × 8
●Nut for Pre-installed Cable Penetrator × 1
●O-ring for Pre-installed Cable Penetrator × 8

このページの先頭へ